Ricon B156 Manuel d'utilisateur

32DPF702.A 2 - 1 II. INSTALLATION he RICON PF7000 Series Express Ramp has been engineered and designed for custom installations. Installa-tion co

2 - 10 32DPF702.A C. CONTROL PANEL INSTALLATION 1. GENERAL SAFETY PRECAUTIONS WARNING! DO NOT TOUCH OR GO NEAR THE CONTROLLER WHILE IT IS P

32DPF702.A 2 - 11 2. CONTROLLER WIRING WARNING! MAKE SURE THAT THE POWER SOURCE IS DISCONNECTED WHEN ROUTING WIRES. THERE IS DANGER OF EL

2 - 12 32DPF702.A 3. CRIMPED RING- 1.5mm2 WIRE a. Refer to Figure 2-19. Strip approximately 6.5 ~ 7.0mm of insulation by using the appropriate wir

32DPF702.A 2 - 13 4. CRIMPED RING- 6mm2 WIRE a. Refer to Figure 2-22. Strip approximately 9.0 ~ 9.5mm of the insulation by using the appropriate

2 - 14 32DPF702.A D. CONTROL PANEL INSTALLATION 1. GENERAL SAFETY PRECAUTIONS WARNING! DO NOT TOUCH THE REAR SIDE OF THE CONTROL PANEL WHIL

32DPF702.A 2 - 15 2. CONTROL PANEL WIRING WARNING! MAKE SURE THAT THE POWER SOURCE IS DISCONNECTED WHEN ROUTING WIRES. THERE IS DANGER OF

2 - 16 32DPF702.A FIGURE 2-26

32DPF702.A 2 - 17 3. CRIMPED - 1.5mm2 WIRE a. Refer to Figure 2-27. Strip approximately 4.75 ± 0.38mm of insulation by using the appropriate wir

2 - 18 32DPF702.A 4. CRIMPED - 6mm2 WIRE a. Refer to Figure 2-30. Strip approximately 9.0 ∼ 10.0mm of insulation by using the appropriate wire st

32DPF702.A 2 - 19 f. Refer to Figure 2-34. Install the tab that was removed from the housing as shown in Figure 2-34. g. Insert the tab’s rete

2 - 2 32DPF702.A ACCESS PANELEYE BOLTSEYE BOLTS FIGURE 2-2: EYE BOLT LOCATIONS f. Refer to Figure 2-3. Rotate timing belt approximately 25-30 time

2 - 20 32DPF702.A This page intentionally left blank. BACK TO TOP

32DPF702.A 2 - 3 REAR ENDMOUNTING HARDWAREMID-SECTIONMOUNTING HARDWAREFRONT MOUNTINGHARDWARERAISED HINGED FLOORROD FIGURE 2-3: INSTALLING MOUNTIN

2 - 4 32DPF702.A a. Refer to Figure 2-4. Slide flutter valve onto holder. b. Refer to Figure 2-4. Place hose clamp over flutter valve and tighten

32DPF702.A 2 - 5 c. Refer to Figure 2-7. Strip .350 - .370” (8.90 - 9.40mm) of insulation from end of the two 8 AWG (6 mm2) wires. Use a crimpin

2 - 6 32DPF702.A f. Refer to Figure 2-11. Insert 14 AWG (1.5 mm2) wires into connector and connect to sensor cable. FIGURE 2-11: CONNECTING SENSO

32DPF702.A 2 - 7 CONDUIT CONNEC TOR (PMA N o. BVND-M257G T)SUPPLIED WITH RAMPCABLE AND CONDUIT (PMA N o. VOHG-17)PROVIDED BY CAR BUILDERMCONNECTOR

2 - 8 32DPF702.A FIGURE 2-13: RAMP WIRING DIAGRAM (SHEET 1 OF 2)

32DPF702.A 2 - 9 FIGURE 2-14: RAMP WIRING DIAGRAM (SHEET 2 OF 2)